Can You Put A French Drain Under A Flower Bed Underground Irrigation Repair Without Digging – All it Takes is a Heat Gun!

You are searching about Can You Put A French Drain Under A Flower Bed, today we will share with you article about Can You Put A French Drain Under A Flower Bed was compiled and edited by our team from many sources on the internet. Hope this article on the topic Can You Put A French Drain Under A Flower Bed is useful to you.

Underground Irrigation Repair Without Digging – All it Takes is a Heat Gun!

I developed this irrigation repair technique out of desperation. A sprinkler head shot out of the ground right next to me one day and landed in a pot. The resulting geyser was spectacular, but the location was terrifying!

The area around this particular sprinkler head was surrounded by cobblestones and brick, and worse, right next to a fence. To make things more difficult, I installed a french drain just a foot away! The riser nipple was missing. Of course the replacement riser wouldn’t even start to screw in! Apparently, the broken off part of the bit was stuck in the t-connector – deep underground! Before I developed this technique, I would have to dig side ditches about 2′ long on each side of the connector, cut the feed lines from each end of the connector, add a sleeve and spacer, and then glue in a replacement t-connector. Not this time! There was too much involved in digging that connector out of the ground!

I have a special tool that I bought from The Home Depot just for this problem. This is the PVC version of “easy-out.” Unfortunately it wouldn’t work! I couldn’t get enough pressure (the connector was buried almost the entire length of the extractor) and kept scraping my knuckles against the fence post. The stand was not made of PVC, but vinyl. It was so smooth that the edges of the extractor knife refused to dig into the inside edge.

But the vinyl melts! i have 1200 W heat gun I bought it for paint removal. The tip of the extractor is metal and I heated the tip of the extractor using this heat gun. Really hot. Sizzling hot! Pushing the extractor straight down the hole, it gently melted into the broken off wart – deep underground! I let it set and cool for a few minutes before twisting it. Two seconds later it broke off the nipple was pulled out!

After screwing in the replacement riser, I moved the irrigation pump to that area to flush out any dirt that had fallen into the connector. I put a new injector head on the replacement riser and guess what? This irrigation repair has been completed. Not just made, I didn’t even have to dig or shovel soil!

The trick was to get the tip of the extractor so hot that it melted into the broken off vinyl bit so it stuck.

A few weeks later I had a different problem. I installed new window boxes along one side wall of my home and wanted to use my built-in irrigation system to water the new flowers. I had a closed riser exactly where I need to put a 4′ riser. Unfortunately, it was an old steel riser that I bumped into several times with the mower, and when I removed the hose, it left the T-connector threads stripped and choked with rust! Unlike most of my irrigation repair projects, this line is very shallow. Shallow enough that I could scrape off the top and really see the damage.

There was nothing I could do to thread the new riser into place, I had to replace the T-connector – or not. I have a pretty complete shop and have metalworking tools that I can use to drill screw thread holes or cut external screw threads. Since I had to go to The Home Depot or Lowe’s anyway to get a replacement t-connector, why not see if they have a pipe threading tool?

The staff at Lowe’s laughed when I asked them for a tool to cut the 1/2″ internal pipe thread for the underground PVC t-connector! Their only advice was to dig it out and replace it. No way! The staff at The Home Depot didn’t laughed out loud, but they also suggested replacing the fittings.

I bought the fittings and also found the perfect tool – 18″ long 1/2″ steel pipe! Once again, 1A 200-watt heat gun came to the rescue. By heating the end of the pipe, the threaded part, I was able to sink it into the buried t-connector. It squealed as it sank in and I quickly pushed it in deeper as I screwed it into place. Without letting it sit, I unscrewed the steel tube to prevent it from being welded into place. I repeated this operation several times until the entire threaded part of the pipe was in the t-connector fitting.

Guess what? New Replacement 4″ PVC Riser Line Threaded Itself! Using heat, pressure and steel threads I was able to partially melt the underground t-connector and cut new threads. Not even a shovelful of soil was dug up for this irrigation fix!

Since then I’ve been helping my neighbors with their irrigation repair projects and they were blown away – “you can actually cut new threads underground without having to dig” – Wow, thanks Bill, really big thanks!

This technique cannot be used for all irrigation repairs. Let’s face it, if the T-connector fitting or connecting tubes crack or break, you’re going to have to dig. But try this tip first and see if it works. You’ll know within minutes if it’s a more serious problem. You’ll get wet there, but you’ll quickly notice heaving around a working sprinkler head if there’s a broken hose or cracked nozzle. Well, at least you tried!

I had that cheap heat gun for $20 for more than twenty years. Not only does it do a great job of lifting paint, I’ve also used it for boat electrical repairs (heat shrink tubing), removing self-adhesive vinyl tiles, contact paper and sanding discs, and even burning charcoal in my charcoal pit. This is NOT a hair dryer – keep it safe, keep it away from you at all times!

In short, I was able to use mine cheap heat gun and a cheaper steel pipe to apply enough heat and pressure to re-form the removed internal threads and enough raw heat to cut the edges of another tool into material that without that tool would require digging up a lot of dirt for those simple irrigation repair projects!

Video about Can You Put A French Drain Under A Flower Bed

You can see more content about Can You Put A French Drain Under A Flower Bed on our youtube channel: Click Here

Question about Can You Put A French Drain Under A Flower Bed

If you have any questions about Can You Put A French Drain Under A Flower Bed, please let us know, all your questions or suggestions will help us improve in the following articles!

The article Can You Put A French Drain Under A Flower Bed was compiled by me and my team from many sources. If you find the article Can You Put A French Drain Under A Flower Bed helpful to you, please support the team Like or Share!

Rate Articles Can You Put A French Drain Under A Flower Bed

Rate: 4-5 stars
Ratings: 7094
Views: 47003813

Search keywords Can You Put A French Drain Under A Flower Bed

Can You Put A French Drain Under A Flower Bed
way Can You Put A French Drain Under A Flower Bed
tutorial Can You Put A French Drain Under A Flower Bed
Can You Put A French Drain Under A Flower Bed free
#Underground #Irrigation #Repair #Digging #Takes #Heat #Gun

Source: https://ezinearticles.com/?Underground-Irrigation-Repair-Without-Digging—All-it-Takes-is-a-Heat-Gun!&id=2647490